PEUGEOT is to highlight its new Built for Business light commercial vehicle conversion programme at the CV Show (April 24-26).

First models in the Built for Business range include:

  • Tipper,
  • Dropside,
  • Luton,
  • Low-Floor Luton,
  • Box Body and
  • Curtainside.

All the conversions are based on the Peugeot Boxer 335 chassis, powered by the 2.0 BlueHDi 160 S&S engine with six-speed manual transmission.

Standard equipment includes air conditioning, an uprated battery and revised dual-leaf rear suspension with anti-roll bar.

Peugeot Built for Business conversions conform to either European Whole Vehicle Type Approval or National Small Series Type Approval regulations and can be ordered from dealers.

Peugeot Boxer Built for Business TipperPeugeot Boxer Built for Business Tipper

Peugeot Boxer Built for Business Tipper models are based on the Boxer 335 L2 single cab and L3 crew cab models. Bodywork features include bolted construction for ease of maintenance.

The front bulkhead/gantry provides a number of load securing points, including one-tonne capacity load securing eyes in the upper structure. The body side board and integrated lever lock assemblies have been tested to burst loads of 1.7 tonnes while the theft-resistant hinges have been tested to a burst load of 1.3-tonnes. Full “Chapter 8” high-visibility markings for the tail board are included. The compact scissor-type underfloor tipping gear includes overload and hose burst protection. The mechanism is designed to be maintenance free throughout the life of the vehicle.

Payloads are up to 1,222kg.

Weights and dimensions

Model L2 Single Cab L3 Crew Cab
Wheelbase 3,450mm 4,035mm
Internal length 2,870mm 2,670mm
Internal width 2,026mm 2,026mm
Sideboard height 400mm 400mm
Tailboard height 600mm 600mm
Overall length 5,895mm 6,100mm
Payload* 1,222kg 1,033kg

 

Peugeot Boxer Built for Business DropsidePeugeot Boxer Built for Business Dropside

The Built for Business Dropside range is built to the same rigorous standards as the Tipper and also features steel and aluminium construction for maximum durability and optimum payload. Three variants of the Dropside will be available, based on the Boxer 335 L2 Single Cab, L3 Single Cab and L3 Crew Cab. The Built for Business Dropside offers payloads up to 1,441kg.

Features include a similar front gantry/bulkhead to the Tipper and 400mm deep side and tailboards made from double-skinned aluminium. The load floor is built using a single piece of non-slip birch plywood, with 800kg capacity retractable load securing rings fitted to its perimeter frame.

Aluminium corner posts are fitted at the rear of the body. These can be lifted out when not required and the side and tailboards removed to provide a flatbed body.

Bolted, modular construction means that a number of options can be easily included. For example; a tool trunk, folding footsteps, grab handles or a tail-lift.

Weights and dimensions

Model L2 Single Cab L3 Single Cab L3 Crew Cab
Wheelbase 3,450mm 4,035mm 4,035mm
Internal length 3,059mm 3,644mm 2,805mm
Internal width 2,026mm 2,026mm 2,026mm
Sideboard height 400mm 400mm 400mm
Tailboard height 400mm 400mm 400mm
Overall length 5,645mm 6,229mm 6,229mm
Payload* 1,441kg 1,366kg 1,253kg

 

Peugeot Boxer Built for Business Luton

The Luton range is available with either the Boxer 335 L3 or L4 Single Cab. All Built for Business Luton bodies feature an aerodynamically designed pod above the Boxer cab, reducing air drag while providing additional storage space in the body.

The body panels are constructed from high quality GRP, built on a robust galvanised steel frame. Alternatively, lightweight aluminium frames will provide up to 80kgs of additional payload.

Both front bulkhead and side panels are fitted with internal kick strips to protect against damage. The interior features both load locking and tie-rail tracks for a range of load restraint options. Additional rows and layouts are available. The rear closure features a lightweight roller shutter door with locking handle.

Standard equipment for the Built for Business Luton includes a 500kg capacity column tail lift, complete with dual controls to enable operation from inside or outside the vehicle. There’s an interior light, while external marker lights are also standard.

Weights and dimensions

Model L3 Single Cab L4 Single Cab
Wheelbase 4,035mm 4,035mm
Internal length 3,480mm 4,150mm
Internal width 2,057mm 2,057mm
Internal height 2,235mm 2,390mm
Volume 16m3 20m3
Payload* 1,147kg 979kg

 

Peugeot Boxer Built for Business CurtainsidePeugeot Boxer Built for Business Curtainside

Peugeot’s Built for Business Curtainside also benefits from an aerodynamic Luton pod over the cab. The Curtainside body provides easy access to the load area from either side. Alternatively, the fully-opening barn doors provide rear access.

The Curtainside body is available with either the Boxer 335 L3 or L4 Single Cab. The body provides a maximum payload of up to 965kgs (with a 17m3 volume) or a maximum volume of 20m3 with a 879kg payload. This enables up to six Euro-pallets to be carried.

Similar construction techniques for the Luton are used for the Curtainside body, with the same lightweight aluminium alternative, yielding up to 75-80kgs more in payload. The reinforced front bulkhead is equipped with a kick strip to guard against damage.

Load restraining equipment includes aluminium V-groove side raves with four pull-up hooks. Lashing rings, providing additional load restraint points are available as an option. The side apertures open up to 2,080mm, to ease loading from either side. The body comes with an interior light and external side marker lights.

Weights and dimensions

Model L3 Single Cab L4 Single Cab
Wheelbase 4,035mm 4,035mm
Internal length 3,480mm 4,150mm
Internal width 2,057mm 2,057mm
Internal height 2,350mm 2,350mm
Volume 17m3 20m3
Payload* 965kg 879kg

 

Peugeot Boxer Built for Business Box Body

The Boxer Built for Business Box Body shares many of its construction features with the Luton and Curtainside.

This includes base and rear frame construction in galvanised steel. A lightweight aluminium option increases payload by up to 80kgs.

The body is available with either Boxer 335 L3 or L4 Single Cab. Features include high-quality GRP panels for lightweight construction. Inside, a kick strip guards against damage. The body provides a load volume of up to 20m3 and payloads up to 1,051kgs.

Standard load restraint equipment includes load locking and tie rail strips. Additional rows and other options are available.

The rear closure is a lightweight roller shutter door with locking handle. Load handling equipment includes a standard 500kg capacity column tail lift. Dual controls enable operation from both inside and outside the vehicle. Lighting equipment includes an interior light with external rear marker lights.

Weights and dimensions

Model L3 Single Cab L4 Single Cab
Wheelbase 4,035mm 4,035mm
Internal length 3,480mm 4,150mm
Internal width 2,057mm 2,057mm
Internal height 2,235mm 2,390mm
Volume 16m3 20m3
Payload* 1,051kg 983kg

 

Peugeot Boxer Built for Business Low Floor LutonPeugeot Boxer Built for Business Low Floor Luton

Since the Peugeot Boxer is on a front-wheel drive chassis it means that low floor bodywork can be used to ease loading access and increase body volume.

The Low Floor Luton provides the option of a high-volume 22m3 Luton body, the largest available in the Boxer Built for Business range. It also provides over a tonne of payload with up to 1,050kgs available.

Body panels are made from high-quality 14mm GRP to provide strength and maximise payload, while the floor is made from non-slip birch plywood. Payload can be increased by around 120kg by opting for lightweight body panels. The front bulkhead is protected from damage by an alloy kick strip.

Both body sides are equipped with load lock strips. At the rear, the standard closure is a pair of flush-fitting barn doors, with a lightweight roller shutter available as an option. Like the standard Luton body, the storage space above the cab is provided by an aerodynamic pod.

Weights and dimensions

Model Low Floor Luton
Internal length 4,080mm
Internal width 2,160mm
Internal height 2,500mm
Overall height 3,200mm
Overall length 6,570mm
Payload* 1,050kg

 

Richard Abbott, Head of National Specialist Fleets at PSA Group, said:

“With the launch of Built for Business light CV conversions, Peugeot is providing certainty for customers that they are buying a vehicle where all parts of the conversion are built to the same exacting standard as the base vehicle.

“All Built for Business light CV conversions carry a full warranty. We can guarantee quick delivery, excellent payload and competitive prices.”

 

Got a spare 30 seconds?

 Help us to provide you with better market insight by completing a very short survey. It is anonymous and only takes 30 seconds. You will get free access to the quarterly results.

Thinking of the switch to electric?

Need help in finding the right electric vehicle for you? Compare driving range, battery capacity, charging time, price, and features to find the perfect EV for you.

logo